Team Shock's Build Diary
Moderators: BeligerAnt, petec, administrator
Re: Team Shock's Build Diary
I have decided to start work on my ants early so that I have some which might actually work for the AWS.
First up is a currently unnamed tracked one. Currently weighs in at 70g so will have some 1mm titanium all round to make it spinner proof.
Next up is Inertia 9
Decided to go 4wd as on the new featherweight which will hopefully improve the drive as well as doubling up the single tooth disc to give a bit more energy in the spinner.
First up is a currently unnamed tracked one. Currently weighs in at 70g so will have some 1mm titanium all round to make it spinner proof.
Next up is Inertia 9
Decided to go 4wd as on the new featherweight which will hopefully improve the drive as well as doubling up the single tooth disc to give a bit more energy in the spinner.
Re: Team Shock's Build Diary
Dude, sweet idea!
Looks a bit vulnerable though. I can see a chassis exposing if a horizontal clocks you one.
Tracked thing is cool too
Harry
Looks a bit vulnerable though. I can see a chassis exposing if a horizontal clocks you one.
Tracked thing is cool too
Harry
For my stuff:
http://bodgeitandhope.blogspot.co.uk/
http://bodgeitandhope.blogspot.co.uk/
- earthwormjim
- Posts: 1190
- Joined: Thu Sep 16, 2010 4:57 pm
- Location: Secret Undisclosed Moonbase Location
Re: Team Shock's Build Diary
Oooh. That is REALLY nice! Great design.
I like it alot.
I like it alot.
-
- Posts: 3716
- Joined: Sun Apr 03, 2005 5:30 pm
- Location: Antrim, Northern Ireland
- Contact:
Re: Team Shock's Build Diary
Re: Team Shock's Build Diary
Got a feeling I'm gonna be pulling an all nighter tonight; Got coursework to get finished AND THEN firmware to write for those ESCs Hope it works; that thing's looking good! :L
Rory Mangles - Team Nuts
Robots: Nuts 2 and many more...
NanoTwo Motor Controllers: https://nutsandbots.co.uk/product/nanotwodualesc
Robots: Nuts 2 and many more...
NanoTwo Motor Controllers: https://nutsandbots.co.uk/product/nanotwodualesc
Re: Team Shock's Build Diary
Time to get to work sorting things out for the next AWS.
I've got a few ants which I haven't fully finished yet so its time to put them into action.
The first job is to finish off Inertia 9 which currently looks like this.
Its a 4WD setup with a more powerful disc and one of Rory's NanoTwo ESCs.
Then Inversion which is still the same as above
Its having a few issues with its tracks so I might change it to 4WD to keep things simple. When run on 3s it should have plenty of push.
Finally there will be some flipper as well. Possibly mANTa again with a new printed shell or something a little different. The other option will be to print one of my kits to use which now look like this
I've got a few ants which I haven't fully finished yet so its time to put them into action.
The first job is to finish off Inertia 9 which currently looks like this.
Its a 4WD setup with a more powerful disc and one of Rory's NanoTwo ESCs.
Then Inversion which is still the same as above
Its having a few issues with its tracks so I might change it to 4WD to keep things simple. When run on 3s it should have plenty of push.
Finally there will be some flipper as well. Possibly mANTa again with a new printed shell or something a little different. The other option will be to print one of my kits to use which now look like this
Re: Team Shock's Build Diary
Time for some pre AWS work so that it wont be a last minute rush as always.
Inertia 9 has been proving difficult, the 4 wheel drive setup was not working as well as I would have liked and needs a bit of a rethink but for now it has been replaced with Inertia 10. I have also rebuilt mANTa with a new printed shell as the old HDPE one got shredded last time out.
Inertia 10 is printing as I type this and should be finished soon.
Inertia 9 has been proving difficult, the 4 wheel drive setup was not working as well as I would have liked and needs a bit of a rethink but for now it has been replaced with Inertia 10. I have also rebuilt mANTa with a new printed shell as the old HDPE one got shredded last time out.
Inertia 10 is printing as I type this and should be finished soon.