Invadants
Moderators: BeligerAnt, petec, administrator
- Team Invade
- Posts: 106
- Joined: Wed Nov 10, 2010 7:13 pm
- Contact:
Re: Team Invade Antweights
Well, while I ponder over that, I've started doing this, which should have no problems with the speed controller
Last edited by Team Invade on Sat Oct 22, 2011 6:44 pm, edited 1 time in total.
Website | YouTube | Photobucket | Build Diary
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
Re: Team Invade Antweights
as people have already pointed out having a bot made from solidly 3d printed white and flexible is very expensive and brittle. best way to do it is to make a frame then screw polycarb or other armour to it
- Simon Windisch
- Posts: 1806
- Joined: Tue Apr 15, 2003 12:00 am
- Location: Reading
- Contact:
Re: Team Invade Antweights
I'm going to see what 3mm Shapeways' "strong white" armour does against spinners at Richmond - possibly.
-
- Posts: 3716
- Joined: Sun Apr 03, 2005 5:30 pm
- Location: Antrim, Northern Ireland
- Contact:
Re: Team Invade Antweights
Ooh, mini Explosion! Implosion? lol
Die Gracefully Robotics
Winner - AWS 39
Winner - AWS 39
- Team Invade
- Posts: 106
- Joined: Wed Nov 10, 2010 7:13 pm
- Contact:
Re: Team Invade Antweights
Stage 2
Flipper gap widened, height and length lowered, part of framework done
91mm,91mm,38.5mm
Flipper gap widened, height and length lowered, part of framework done
91mm,91mm,38.5mm
Last edited by Team Invade on Sat Oct 22, 2011 6:45 pm, edited 1 time in total.
Website | YouTube | Photobucket | Build Diary
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
- Team Invade
- Posts: 106
- Joined: Wed Nov 10, 2010 7:13 pm
- Contact:
Re: Invadants
Last edited by Team Invade on Sat Oct 22, 2011 6:45 pm, edited 1 time in total.
Website | YouTube | Photobucket | Build Diary
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
- Team Invade
- Posts: 106
- Joined: Wed Nov 10, 2010 7:13 pm
- Contact:
Re: Invadants
I've sorted out the front panels, but sketchup was being awkward and wouldn't enclose the structure without putting two extra lines in:
Would this be a problem while printing?
Would this be a problem while printing?
Website | YouTube | Photobucket | Build Diary
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
- Team Invade
- Posts: 106
- Joined: Wed Nov 10, 2010 7:13 pm
- Contact:
Re: Invadants
Re-mounted the servo and tightened a few screws after Kidderminster, wasn't too happy with the performance there
Due to this the flipper is flush to the ground once more, was a bit of a pain not being
Website | YouTube | Photobucket | Build Diary
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
Featherweight UK Champion
Heavyweight Robot Wars Champion
Heavyweight Tag Team Champion
Featherweight Tag Team Champion
-
- Posts: 3716
- Joined: Sun Apr 03, 2005 5:30 pm
- Location: Antrim, Northern Ireland
- Contact:
Re: Invadants
Oh, I didn't know you'd finished it. Looks great. Are you planning on attending the AWS? Or is it just for the sideshows at the bigger events?
Die Gracefully Robotics
Winner - AWS 39
Winner - AWS 39
Re: Invadants
Actually Dave thats the old one.