http://www.hobbyking.com/hobbyking/stor ... duct=10915
I've ordered some for a little project I'm working on. I'll let you if if they're any good. I'm sure on these forums have already tried them though.
the fleaweight diet?
Moderators: BeligerAnt, petec, administrator
- earthwormjim
- Posts: 1190
- Joined: Thu Sep 16, 2010 4:57 pm
- Location: Secret Undisclosed Moonbase Location
Re: the fleaweight diet?
Hey guys.
I've been rebuilding Little Devil properly and I've managed to install the servo and compact it all, and it comes to 75g...without the flipper I have to lose about 10g to get the flipper on (made from CF, muchos Gracias to Josh for that). I think I can do it, may involve a lot of holes, and I'm hoping 1mm circuit board weighs less than 2mm HDPE does .
On the plus side, I finally got LD to self right for the first time since I got it
I've been rebuilding Little Devil properly and I've managed to install the servo and compact it all, and it comes to 75g...without the flipper I have to lose about 10g to get the flipper on (made from CF, muchos Gracias to Josh for that). I think I can do it, may involve a lot of holes, and I'm hoping 1mm circuit board weighs less than 2mm HDPE does .
On the plus side, I finally got LD to self right for the first time since I got it
Re: the fleaweight diet?
I think the circuit board will be roughly half the weight of the hdpe, I imagine they are about the same density
RPD International
www.RPDintl.com
www.RPDintl.com
Re: the fleaweight diet?
i got some 1mm hdpe you could have dave
For my stuff:
http://bodgeitandhope.blogspot.co.uk/
http://bodgeitandhope.blogspot.co.uk/
Re: the fleaweight diet?
I've got plenty, but thanks for the offer Haz. I needed something thinner than the 2mm but also a lot stiffer than HDPE, hence the circuit board.
Re: the fleaweight diet?
okay sure (try fitting 10mm armour into a flea its faaar to hard )
For my stuff:
http://bodgeitandhope.blogspot.co.uk/
http://bodgeitandhope.blogspot.co.uk/
Re: the fleaweight diet?
These could be just the thing for fleas, only 5g each!
http://www.himodel.com/electric/HiModel ... _Pack.html
http://www.himodel.com/electric/HiModel ... _Pack.html
Re: the fleaweight diet?
hey, need some more lightening advice
my spinner (not the drum one) is a bit too heavy, its 72g withought armour, and i need armour
parts im using are:
2 50:1 motors with tiny wheels (wheels are 1g each)
2 small servo boards, with resistors fitted
12g outrunner with a 10g disc
5g dsm2 rx with esc's soldered directly to it(badly )
180mah 7.4v lipo
1mm polycarbonate
1 hobbywing 10a esc
i think the obvious solution is to get a smaller batter, but is their anything else?
my spinner (not the drum one) is a bit too heavy, its 72g withought armour, and i need armour
parts im using are:
2 50:1 motors with tiny wheels (wheels are 1g each)
2 small servo boards, with resistors fitted
12g outrunner with a 10g disc
5g dsm2 rx with esc's soldered directly to it(badly )
180mah 7.4v lipo
1mm polycarbonate
1 hobbywing 10a esc
i think the obvious solution is to get a smaller batter, but is their anything else?
For my stuff:
http://bodgeitandhope.blogspot.co.uk/
http://bodgeitandhope.blogspot.co.uk/