fleas
Moderators: BeligerAnt, petec, administrator
- earthwormjim
- Posts: 1190
- Joined: Thu Sep 16, 2010 4:57 pm
- Location: Secret Undisclosed Moonbase Location
- earthwormjim
- Posts: 1190
- Joined: Thu Sep 16, 2010 4:57 pm
- Location: Secret Undisclosed Moonbase Location
-
- Posts: 3716
- Joined: Sun Apr 03, 2005 5:30 pm
- Location: Antrim, Northern Ireland
- Contact:
- earthwormjim
- Posts: 1190
- Joined: Thu Sep 16, 2010 4:57 pm
- Location: Secret Undisclosed Moonbase Location
- earthwormjim
- Posts: 1190
- Joined: Thu Sep 16, 2010 4:57 pm
- Location: Secret Undisclosed Moonbase Location
Hi guys.
I am after a bit of advice on tx setup...
Bruce used to work on an old 2.4 compatible basic heli TX,with a mechanical mixer. I recently swapped to using my dx6i,and removed the mechanical mixer.So far,so good!!
Now I have an antweight up and running,I thought it would be fun to set Bruce up to work on the old TX,so that I could run them both together,but when I tried,it all worked ok,other than the forweward/backwards stick movement was reversed. After trying all different combinations,and getting nowhere,I decided to set Bruce back up on the dx6i,without the mechanical mixer... The foreward/backwards is still reversed,even after resetting the tx and setting up the mixes again...
MIX1
ELEV + AILE ACT
RATE L -100% R -100%
SW ON TRIM ACT
MIX2
AILE + ELEV ACT
RATE D +100% U +100%
SW ON TRIM ACT
Anyone got any ideas??
Cheers James.
I am after a bit of advice on tx setup...
Bruce used to work on an old 2.4 compatible basic heli TX,with a mechanical mixer. I recently swapped to using my dx6i,and removed the mechanical mixer.So far,so good!!
Now I have an antweight up and running,I thought it would be fun to set Bruce up to work on the old TX,so that I could run them both together,but when I tried,it all worked ok,other than the forweward/backwards stick movement was reversed. After trying all different combinations,and getting nowhere,I decided to set Bruce back up on the dx6i,without the mechanical mixer... The foreward/backwards is still reversed,even after resetting the tx and setting up the mixes again...
MIX1
ELEV + AILE ACT
RATE L -100% R -100%
SW ON TRIM ACT
MIX2
AILE + ELEV ACT
RATE D +100% U +100%
SW ON TRIM ACT
Anyone got any ideas??
Cheers James.
- joey_picus
- Posts: 1137
- Joined: Tue Jan 13, 2009 1:51 pm
- Location: Lancaster, Lancashire
- Contact:
I've had that issue a few times - in each case swapping the servo leads for the speed controller around so they plug into the 'wrong' channel has actually worked (combined with a bit of servo reversing)
Joey McConnell-Farber - Team Picus Telerobotics - http://picus.org.uk/ - @joey_picus
"These dreams go on when I close my eyes...every second of the night, I live another life"
"These dreams go on when I close my eyes...every second of the night, I live another life"
- earthwormjim
- Posts: 1190
- Joined: Thu Sep 16, 2010 4:57 pm
- Location: Secret Undisclosed Moonbase Location
Cheers Joey.Joey wrote:I've had that issue a few times - in each case swapping the servo leads for the speed controller around so they plug into the 'wrong' channel has actually worked (combined with a bit of servo reversing)
I will have another play.
Silly thing is,the old TX doesnt have a facility for servo reversing,and I am sure it used to work!!