Part recommendation
Moderators: BeligerAnt, petec, administrator
Re: Part recommendation
Diagram updated because ocd....
ProtoBot - http://robotwars101.org/forum/viewtopic.php?f=1&t=2471
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
Re: Part recommendation
Just a thought, but if I cut the wires on the battery and connect the esc between the cuts, how safe is it to charge the battery with the esc attached.
Why hasn't someone invented a small bridge that can be placed in between the battery, NanoTwo and ESC instead of cutting the cables.
Also just realised that i'm probably going to need a on/off switch because of the blade. So can I get a link to a part and some advise as to where to splice it into the diagram.
I figure once the diagram is 100% done, ill have a working spinner by christmas.
Why hasn't someone invented a small bridge that can be placed in between the battery, NanoTwo and ESC instead of cutting the cables.
Also just realised that i'm probably going to need a on/off switch because of the blade. So can I get a link to a part and some advise as to where to splice it into the diagram.
I figure once the diagram is 100% done, ill have a working spinner by christmas.
ProtoBot - http://robotwars101.org/forum/viewtopic.php?f=1&t=2471
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
Re: Part recommendation
You mean a Y lead?oxhey wrote: Why hasn't someone invented a small bridge that can be placed in between the battery, NanoTwo and ESC instead of cutting the cables.
I put switches in by cutting the red wire on the nanotwo and connecting it, the brushless ESC red wire also attaches to the switch. then splice in the brushless ESC black wire to the black wire on the nano two. You should NEVER have to cut the wires on the battery.
Nuts And Bots - For all your components and ready built antweights!
Alex Shakespeare - Team Shakey / Nuts And Bots / Team Nuts:
AWS 44, 45, 49, 51 & 55 Winner - Far too many robots!
Alex Shakespeare - Team Shakey / Nuts And Bots / Team Nuts:
AWS 44, 45, 49, 51 & 55 Winner - Far too many robots!
Re: Part recommendation
What is this "Y" lead you speak of? Clearly I know nothing 8)Shakey wrote:You mean a Y lead?oxhey wrote: Why hasn't someone invented a small bridge that can be placed in between the battery, NanoTwo and ESC instead of cutting the cables.
I put switches in by cutting the red wire on the nanotwo and connecting it, the brushless ESC red wire also attaches to the switch. then splice in the brushless ESC black wire to the black wire on the nano two. You should NEVER have to cut the wires on the battery.
Can you advise on where I can get this. Iv had a quick look on hobbyking and the y leads are for servos and not power.
Ill work on the updated diagram tomorrow when words start to make sense
ProtoBot - http://robotwars101.org/forum/viewtopic.php?f=1&t=2471
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
Re: Part recommendation
Well you'd have to make one.
Nuts And Bots - For all your components and ready built antweights!
Alex Shakespeare - Team Shakey / Nuts And Bots / Team Nuts:
AWS 44, 45, 49, 51 & 55 Winner - Far too many robots!
Alex Shakespeare - Team Shakey / Nuts And Bots / Team Nuts:
AWS 44, 45, 49, 51 & 55 Winner - Far too many robots!
Re: Part recommendation
Damn, was hoping you weren't going to say that.Shakey wrote:Well you'd have to make one.
Right so a smaller diagram will be required inside the main one to show the y lead.
Okay then, where do I start with the y lead. Im assuming that its not done completely from scratch and that its a few cables with the right connections that get cut. (Reminds me I need to learn the names of the connectors )
ProtoBot - http://robotwars101.org/forum/viewtopic.php?f=1&t=2471
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
Re: Part recommendation
Right diagram has been updated. I've added in a zoomed section to see the Y part.
From what I understand, the wires are joined and connected to the original connector from the NanoTwo and use electrical tape to cover up the join.
Would the black cable from the switch connect in with the black from the NanoTwo and ESC?
The switch I have found is this http://www.robotshop.com/uk/sfe-on-off- ... witch.html , I think it will work unless you have other suggestions.
Updated Diagram:
From what I understand, the wires are joined and connected to the original connector from the NanoTwo and use electrical tape to cover up the join.
Would the black cable from the switch connect in with the black from the NanoTwo and ESC?
The switch I have found is this http://www.robotshop.com/uk/sfe-on-off- ... witch.html , I think it will work unless you have other suggestions.
Updated Diagram:
ProtoBot - http://robotwars101.org/forum/viewtopic.php?f=1&t=2471
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
Re: Part recommendation
Your last diagram wouldn't be able to turn the robot off and the switch would short the battery. You want something more like this:
Also that switch would be huge, you want something more this size:
Also that switch would be huge, you want something more this size:
Nuts And Bots - For all your components and ready built antweights!
Alex Shakespeare - Team Shakey / Nuts And Bots / Team Nuts:
AWS 44, 45, 49, 51 & 55 Winner - Far too many robots!
Alex Shakespeare - Team Shakey / Nuts And Bots / Team Nuts:
AWS 44, 45, 49, 51 & 55 Winner - Far too many robots!
Re: Part recommendation
Ah, I see. My diagram wasn't that far off then
Do you have a link to where to get that kind of switch?
EDIT: would this switch be better - http://www.robotshop.com/uk/tamiya-mini ... h-2pk.html
Do you have a link to where to get that kind of switch?
EDIT: would this switch be better - http://www.robotshop.com/uk/tamiya-mini ... h-2pk.html
ProtoBot - http://robotwars101.org/forum/viewtopic.php?f=1&t=2471
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
SUSPENDED! - I dont have the time/money to fully commit and I may have killed a motor and my NanoTwo !
I may give this another go at some point, but for now its over.
-
- Posts: 109
- Joined: Fri Oct 05, 2012 12:37 am
- Location: Eastleigh, nr Southampton
- Contact:
Re: Part recommendation
If your in the UK, best place is ebay - using a UK only search, results below.
http://www.ebay.co.uk/sch/i.html?_odkw= ... e&_sacat=0
These are the ones I purchased: http://www.ebay.co.uk/itm/5-x-Mini-Sub- ... SwxN5Wbbdo
http://www.ebay.co.uk/sch/i.html?_odkw= ... e&_sacat=0
These are the ones I purchased: http://www.ebay.co.uk/itm/5-x-Mini-Sub- ... SwxN5Wbbdo
Some projects done: Wirelessly controlled mechanical hand/arm
Heavyweight: Short Circuit
Antweight robot : Locking wheel nuts, dell-apidated bANTtry...
Featherweight : Wanna Choppa, CASPer
Check out http://www.Roboteernat.co.uk for more details
Heavyweight: Short Circuit
Antweight robot : Locking wheel nuts, dell-apidated bANTtry...
Featherweight : Wanna Choppa, CASPer
Check out http://www.Roboteernat.co.uk for more details