Search found 227 matches
- Mon Jan 29, 2018 6:33 pm
- Forum: Questions (and answers)
- Topic: Tx and RX question
- Replies: 5
- Views: 7777
Tx and RX question
Could I have 1 transmitter that is bind to two differnt RX. I wouldn’t want to control both RX at the same time. However would I have to continually bind if switching between the two. E.g I could turn robot 1 off and robot 2 on and I could instantly control it Or would I have to rebind robot 2. My R...
- Sun Jan 28, 2018 5:22 pm
- Forum: Antweights
- Topic: Hello, and a modular arduino controlled bot.
- Replies: 6
- Views: 6022
Re: Hello, and a modular arduino controlled bot.
Looks awesome. Those leads weigh a surprising amount some times.
- Sun Jan 28, 2018 5:15 pm
- Forum: Antweights
- Topic: Build Diary: Prototype Robot
- Replies: 11
- Views: 9953
Re: Build Diary: Prototype Robot
Your white and red wire soldering looks like it could be touching. Which will interfere with the servo signal. Make sure there is no connecting solder or wire. I had this problem with the dasmikro when I first soldered it.
- Wed Jan 24, 2018 6:36 pm
- Forum: Antweights
- Topic: "Flip-it” new build/project
- Replies: 81
- Views: 151173
Re: "Flip-it” new build/project
More pictures. He’s a little wonky. Once nuts were all tightened haha. Added switch on the back of robot. https://preview.ibb.co/n1SwPG/19_B87_FCD_BC3_F_4732_9_D10_D254_E3_F58_FE4.jpg https://preview.ibb.co/gUtEBw/2_B1_BF77_C_E961_491_B_A982_94_F62018_AD2_B.jpg https://preview.ibb.co/bUVGPG/B33_DB6_...
- Wed Jan 24, 2018 7:50 am
- Forum: Antweights
- Topic: The adventures of an antweight robot building nerb
- Replies: 24
- Views: 58849
Re: The adventures of an antweight robot building nerb
A few people just use a bolt at either end of the robot. I used a push rod. Recommended by Peter on this forum.
https://www.ebay.co.uk/itm/CARBON-FIBRE ... 2749.l2649
Really strong.
https://www.ebay.co.uk/itm/CARBON-FIBRE ... 2749.l2649
Really strong.
- Tue Jan 23, 2018 11:05 pm
- Forum: Antweights
- Topic: The adventures of an antweight robot building nerb
- Replies: 24
- Views: 58849
Re: The adventures of an antweight robot building nerb
Hello, I made a polycarbonate clamp. Thin strip over the top of servo and a screw at either end of the servo into the base of the chassis. I’ve also used a mix of 3mm and 2mm screws. I found 3mm a little bulky when fiddling around with the inside of the robot. They seemed to get in the way. Only a t...
- Mon Jan 22, 2018 10:23 pm
- Forum: Antweights
- Topic: "Flip-it” new build/project
- Replies: 81
- Views: 151173
- Sun Jan 21, 2018 4:50 pm
- Forum: Antweights
- Topic: "Flip-it” new build/project
- Replies: 81
- Views: 151173
Re: "Unnamed" new build/project
Robot nearly complete. Weighs in at 154g. To do: Drill holes to reduce weight. Trim more wires and add an external switch. Remove paper template and plastic protector. Attach roll bars as robot can get stuck on its side. Attach servo to flipper panel. Possible redesign of inners to protect electroni...
- Fri Jan 19, 2018 4:54 pm
- Forum: Antweights
- Topic: "Flip-it” new build/project
- Replies: 81
- Views: 151173
- Thu Jan 18, 2018 11:40 pm
- Forum: Antweights
- Topic: Eric - Build Diary
- Replies: 8
- Views: 7698
Re: Eric - Build Diary
Not sure on weight. don’t buy the set, as they are only 30rpm motors. Super slow