Search found 1160 matches
- Wed Oct 26, 2016 10:57 am
- Forum: Antweights
- Topic: Part recommendation
- Replies: 55
- Views: 43551
Re: Part recommendation
TBH, that one would probably do you fine. With a temperature controlled iron you'll want to solder with it at around 350C, assuming the temperature setting is accurate. If you're using unleaded solder you may want to swap to using this stuff as it's so much nicer to solder with: https://www.amazon.c...
- Wed Oct 26, 2016 10:05 am
- Forum: Antweights
- Topic: Part recommendation
- Replies: 55
- Views: 43551
Re: Part recommendation
You shouldn't need any extra wires, just cut the wire and solder in a switch. The wires on the ESC will likely need cutting to length anyway so you should have plenty spare from that if needed. Make sure to tin everything properly before soldering it else you'll likely have weak joints. You're ESC i...
- Tue Oct 25, 2016 2:38 pm
- Forum: Events
- Topic: Antweight World Series 51 - Peasedown St. John, 29th October 2016
- Replies: 36
- Views: 39662
Re: Antweight World Series 51 - Peasedown St. John, 29th October 2016
Yeah, I'll probably have one, if not Alex usually does.
- Tue Oct 25, 2016 1:26 pm
- Forum: Events
- Topic: Antweight World Series 51 - Peasedown St. John, 29th October 2016
- Replies: 36
- Views: 39662
Re: Antweight World Series 51 - Peasedown St. John, 29th October 2016
I've signed up with BullyDozer but am gonna try get Drumbledore running before next weekend so I can finally have an all spinner team.
- Sun Oct 23, 2016 10:27 pm
- Forum: Antweights
- Topic: Part recommendation
- Replies: 55
- Views: 43551
Re: Part recommendation
If you need some extra inspiration, this is a similar design which was very successful at the last AWS.
- Sun Oct 23, 2016 9:29 pm
- Forum: Antweights
- Topic: Part recommendation
- Replies: 55
- Views: 43551
Re: Part recommendation
Those motor support bars will want to be thicker than that if it's gonna survive any decent hits; they're gonna be handling a lot of force!
- Wed Oct 19, 2016 7:41 pm
- Forum: Antweights
- Topic: Part recommendation
- Replies: 55
- Views: 43551
Re: Part recommendation
The DYS motors need a 5mm bearing. I use the 5x8x2.5mm ones from here : http://www.ebay.co.uk/itm/W-FLANGE-MODE ... hash=item0
The flange makes it easier to ensure it doesn't fall out.
The flange makes it easier to ensure it doesn't fall out.
- Tue Oct 18, 2016 11:16 pm
- Forum: Antweights
- Topic: Help!!!
- Replies: 8
- Views: 6742
Re: Help!!!
Even if the throttle isn't low you should be getting beeps. Sounds like you're not getting any signal from the receiver. You sure the servo plug is plugged in the right way up? (Yellow wire closest to the heatshrink)
- Tue Oct 18, 2016 9:44 pm
- Forum: Antweights
- Topic: Help!!!
- Replies: 8
- Views: 6742
Re: Help!!!
Yeah, if you cut either of the other two then the ESC isn't gonna do much. Resolder it, cut the red wire, and you should be good.
- Tue Oct 18, 2016 8:26 pm
- Forum: Antweights
- Topic: Help!!!
- Replies: 8
- Views: 6742
Re: Help!!!
Does the motor beep when you power it up? It should beep 3 times in a rising tone, and then do a longer beep to signify that everything's ok and it's got signal. It sounds like it may be a motor connection issue.