Search found 10 matches

by Anty-social
Mon Aug 05, 2019 8:25 am
Forum: Antweights
Topic: Pre modded servo boards for escs?
Replies: 39
Views: 31921

Re: Pre modded servo boards for escs?

Oops my mistake, I just misunderstood. However no damage was done and I have now set it to bind mode. Thank you so much for all your help! :D
by Anty-social
Sun Aug 04, 2019 8:59 pm
Forum: Antweights
Topic: Pre modded servo boards for escs?
Replies: 39
Views: 31921

Re: Pre modded servo boards for escs?

I'm using a Redcon 2204. With your advice (thank you!) , I have got power to it. However, for some reason it doesn't want to bind. I have tried it on 3 other identical receivers and the results are the same. I will put the pic here. https://gyazo.com/3c0ae925ba9bd2506544010ec92a5034.jpg Am I doing s...
by Anty-social
Sun Aug 04, 2019 5:11 pm
Forum: Antweights
Topic: Pre modded servo boards for escs?
Replies: 39
Views: 31921

Re: Pre modded servo boards for escs?

Is the signal pin the top, centre or bottom one? I don't really want to blow up any more receivers after a couple of early mistakes.
by Anty-social
Sun Aug 04, 2019 11:16 am
Forum: Antweights
Topic: Pre modded servo boards for escs?
Replies: 39
Views: 31921

Re: Pre modded servo boards for escs?

Sorry if this is a bit of a stupid question but where do you put the battery connector? I assume I connect it to the rx when using servo boards but I am unsure about where.
by Anty-social
Mon Jul 01, 2019 5:00 pm
Forum: Questions (and answers)
Topic: 3D Printer recommendations?
Replies: 1
Views: 10167

3D Printer recommendations?

Please could anyone recommend a good 3D printer for someone who wants to start printing antweights? Ideally it should be as cheap as possible and not be too difficult to set up. The Creality Ender 3 looks like it could suit my needs. Is this a good printer, and is it able to print well with ABS? Wou...
by Anty-social
Fri Jun 28, 2019 8:35 pm
Forum: Events
Topic: Antweight World Series 58 - 29th June 2019
Replies: 84
Views: 73742

Re: Antweight World Series 58 - 29th June 2019

Does anyone want to cluster a flea as part of an ant cluster? One of the robots inside my cluster has a broken ESC and so I was wondering if anyone wanted to drive one of theirs with it. If nobody wants to I will just run the flea by itself (with ballast) :D .
by Anty-social
Fri May 17, 2019 9:22 pm
Forum: Fleaweights
Topic: Flea won't self-right
Replies: 6
Views: 26925

Re: Flea won't self-right

Thank you for your responses I haven't been able to try them today as I have not had a lot of time, and when I tried to modify the robot I broke a part of the hinge. It's now fixed and I should be able to try to fix the self-righting it tomorrow. Because of how it is built (not that well!) its wheel...
by Anty-social
Thu May 16, 2019 8:36 pm
Forum: Fleaweights
Topic: Flea won't self-right
Replies: 6
Views: 26925

Re: Flea won't self-right

Thanks for the help

Here are the images
Image
Image
Image
Image
by Anty-social
Thu May 16, 2019 5:41 pm
Forum: Fleaweights
Topic: Flea won't self-right
Replies: 6
Views: 26925

Re: Flea won't self-right

The photos I attached didn't show. Can anyone help with this?
by Anty-social
Thu May 16, 2019 5:41 pm
Forum: Fleaweights
Topic: Flea won't self-right
Replies: 6
Views: 26925

Flea won't self-right

I have recently created a fleaweight flipper. Its main purpose is to be part of an antweight cluster and I don't think it fits in the fleaweight cube anyway, but i would still rather not go above 75g. It already weighs 74g so no excessively heavy solutions please! I have had to move the hinge forwar...